祝日に関するお知らせ: 10月1日から4日まで、通常どおりご注文いただけます。 製造・納期は10月5日までとなります。 生産計画を適切に調整してください。詳細はこちら>>

基板クイック試作

カスタム基板試作サービス


PCB Solder mask

Solder mask or solder stop mask or solder resist is a thin lacquer-like layer of polymer that is usually applied to the copper traces of a printed circuit board (PCB) for protection against oxidation and to prevent solder bridges from forming between closely spaced solder pads. A solder bridge is an unintended electrical connection between two conductors using a small blob of solder. PCBs use solder masks to prevent this from happening. Solder mask is not always used for hand-soldered assemblies but is essential for mass-produced boards that are soldered automatically using reflow or Wave Solder techniques. Once applied, openings must be made in the solder mask wherever components are soldered, which is accomplished using photolithography. Solder mask is traditionally green but is now available in many colors.

Solder mask comes in different media depending upon the demands of the application. The lowest-cost solder mask is an epoxy liquid that is silkscreened through the pattern onto the PCB. Other types are the liquid photoimageable solder mask (LPSM or LPI) inks and dry-film photoimageable solder mask (DFSM). LPSM can be silkscreened or sprayed on the PCB, exposed to the pattern and developed to provide openings in the pattern for parts to be soldered to the copper pads. DFSM is vacuum-laminated on the PCB then exposed and developed. All three processes typically go through a thermal cure of some type after the pattern is defined although LPI solder masks are also available in the ultraviolet (UV) cure.

In electronic design automation, the solder mask is treated as a layer of the printed circuit board and is described as a Gerber file like any other layer, such as the copper and silkscreen layers. Typical names for these layers include tStop/bStop (EAGLE), LSMVS/LSMRS (WEdirekt) or GTS/GBS (Gerber and many others).

The functions of the solder mask layer on the PCB board are shown:

.Preventing the physical breakage of a conductor circuit

.Preventing short circuit from bridge connection in the soldering process

.Preventing the copper layer from oxidation

.Prevent short circuit between conductive lines and solder joints when proceeding reflow soldering, wave soldering, and manual welding

.Its high Insulating brings the possibility to the high density of PCB boards 

The solder mask is mainly Liquid UV Photo-imageable Ink with green, red, blue, yellow, white, black and purple colors, green should be the most commonly used one. And according to those colors available,  there are some points in our production requirement for your reference.

.The cost for green, blue, red, blue, yellow, white and black are the same without extra charge, and extra charge needed for the purple, matte green, matte black mask.

.For solder bridge, the spacing between IC pads should be min 0.2 mm for green color,others require min 0.25 mm

.As for normal case, the lead time for green mask should be shorter than others

.Since we just refer to solder bridge above, now comes to a briefly knowing for it: 

The solder bridge is the green oil between the two pads or the IC pins, For its narrow need, so it is called the solder resist bridge. If the distance between the pins is too small to meet the factory process, it will be recommended to cancel it and proceeded with full mask openings.

solder mask.jpg

Mask opening: any area without mask printing can be called window opening, it includes areas for solder PAD, paste PAD, trenching, etc.

There are total 9 solder masker color in PCBWay, here is the sample PCBWay ruler:

solder mask-2.jpg

If you are interested in, more information please check our gift shop


コメント (0)
注:このメッセージは、PCBWayとお客様との間の毎日の通信専用です。 応答は非常にタイムリーではありません。
緊急の質問がある場合は、セールスマンにお問い合わせください!
アップロードできるファイルは合計で1つのみです。 各ファイルは2MBを超えることはできません。 JPG、JPEG、GIF、PNG、BMPをサポート